All Rights Reserved.Ĭonfigure Monit Service Manager on Ubuntu 22.04 If your service wasn’t started, use the following command: sudo systemctl start monitĪlso, you can check your Monit version: sudo monit -version Outputīuilt with ssl, with ipv6, with compression, with pam and with large filesĬopyright (C) 2001-2022 Tildeslash Ltd. └─2654 /usr/bin/monit -c /etc/monit/monitrc Process: 2648 ExecStart=/etc/init.d/monit start (code=exited, status=0/SUCCE SS) Loaded: loaded (/etc/init.d/monit generated)Īctive: active ( running) since Wed 12:09:16 UTC 10s ago rvice - LSB: service and resource monitoring daemon.To check the status of Monit, run the command below: sudo systemctl status monit -no-pager -l Output Then, use the following command to install the Monit: sudo apt install monit -y Manage Monit ServiceĪt this point, your Monit service should be activated on your server. First, update your local package index with the command below: sudo apt update & sudo apt upgrade -y The Monit packages are available in the default Ubuntu 22.04 repository. To do this, you can follow our guide on Initial Server Setup with Ubuntu 22.04. To complete this guide, you must log in to your server as a non-root user with sudo privileges and set up a basic firewall. Finding the right driver version seemed to be the crucial step for me.Steps To Install Monit Manager on Ubuntu 22.04 Ideally, you should be able to run nvidia-smi after a correct installation. Note that having a single driver version and removing all the others is highly recommended. Navigate to the terminal using Ctrl + Alt + F1 and purge all the current driver version using sudo apt-get remove -purge nvidia* and reinstall a different version of the driver. If the incorrect driver version was installed, the gui may not open.If the incorrect driver was installed, the gui won't open even on the main screen. If there is no driver, you would be unable to switch. Switch from Intel graphics to NVIDIA graphics - As mentioned in the previous comments, this can be done by sudo prime-select nvidia followed by a reboot.Instead I used the command sudo ubuntu-drivers list to check the list of compatible drivers and followed it up with sudo apt install nvidia-driver. The one recommended in the ubuntu S/W center did not work for me. ![]() It is highly likely that the HDMI will be disconnected which is why the external monitor is not getting detected.Note that this is not an absolutely necessary step. Switch from lightdm to gdm - The effectiveness of using lightdm as the display manager over gdm has been documented here (although this was only an issue in a different flavor of Linux).I had tried multiple things before I got it working properly. ![]() In my case, I have both a built in Intel and external nvidia graphics. This seems to be a very common issue that is also very situation specific. Please also comment, if you need any further information I also installed lightdm with no changes. ![]() Sudo xrandr -output HDMI-1 -mode 1920x1080 -pos 0x0 I then installed another driver, but that didn't change anything.Īfter running these Commands the monitor is in mirror mode, but it shows up as disconnected in xrandr sudo xrandr -output HDMI-1 -auto I have tried to install different drivers from Software&Updates->Additional Drivers,Īnd also added PPA and installed the recommended drivers sudo add-apt-repository ppa:graphics-drivers/ppa Resources: irq:133 memory:93000000-93ffffff memory:50000000-5fffffff memory:60000000-61ffffff ioport:4000(size=128)Ĭapabilities: pciexpress msi pm vga_controller bus_master cap_list rom fbĬonfiguration: depth=32 driver=i915 latency=0 resolution=1920,1080 HDMI-2 disconnected (normal left inverted right x axis y axis)Ĭapabilities: pm msi pciexpress bus_master cap_list rom HDMI-1 disconnected (normal left inverted right x axis y axis)ĭP-2 disconnected (normal left inverted right x axis y axis) Output of xrandr: Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 16384 x 16384ĮDP-1 connected primary 1920x1080+0+0 (normal left inverted right x axis y axis) 381mm x 214mmĭP-1 disconnected (normal left inverted right x axis y axis) I have searched for quite some time, but couldn't find a solution in any of the previous/similar threads. It works just fine, if I am using Windows. I just installed Ubuntu 22.04 as Dualboot on my Laptop, and it does not recognize my second monitor.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |